Share your SWITCH v2.0 Experience

@laga,

I’m assuming that I’m not framing the question correctly as I’m trying to recollect the exact question from the exam. However, Cisco is trying to ask if the Switch will tag the VLAN 1 or VLAN 166 on the Switchport.

number 2 is correct but we need one more option.

@Waseem

How accurate are those answers?

passed today. most of the MCQ is valid. for drag n drop was tested for only 1 question. its new question. but similar to the old one. RSPAN related. not that hard. lab was same. I just use the premium only no other resource.Good Luck folks!!!. Off to Tshoot.

@anon guy

congrats for passing your exam,
I am a premium member too and i use this site as my primary studying source. but i have not any section called MCQ in this site, can you please tell me where to find the MCQ on this site

please is the Certprepare dump enough to pass the exam ?

please is the Certprepare dump enough to pass the exam ?

congrats anon, thanks for your update

Mcq which is multiple choice question. Most of the question is from hsrp,vrrp,glbp,dhcp snooping, ip sourceguard. DAI, cdp,lldp, etherchannel related, few port security and storm control n private vlan. would say like 8 new questions, some reworded. Yes premium is enough. I did all the topic flash test and then did my own note which topic I’m weak. All this in 2week prep time. I suggest read the explanation behind the answer. The new questions one from private vlan, one about cdp and one about storm control. Other don’t quite remember.

@Nasa please can you tell me which 2 other dumps ?

Passed 975/1000..

Pass the test with a premium account

I have a Premium account valid until February 1st if someone interested who writes me private to the attached address, (remove pipe). The price is $13

Thanks Network TUT!!!
almfark22|@|gmail|.com

Which two commands display IP source guard bindings? (Choose two)
A. show ip guard source
B. show ip dhcp snooping database
C. show ip verify source
D. show ip source binding
E. show ip dhcp binding
ANS: CD o BD ???

Which type of load balancing is most appropiate for an EthernetChannel that passes traffic from multiples sources to a single end device?
A. source MAC address and source IP address
B. destination MAC address forwarding
C. source and destination IP address forwarding
D. destination IP address forwarding
ANS: B?

Which command enables a RADIUS server configuration to use vendor-proprietary attributes?
A. radius-server configure-nas
B. radius-server attribute nas-port extended
C. radius-server host non-standard
D. radius-server vsa send authentication
Answer: D o C?

Refer to the exhibit.
Which EtherChannel load balancing algorithm should be used to optimize the EtherChannel links between switches?
A. Source MAC
B. Source-dest MAC
C. Destination IP
D. Destination MAC
ANS?

Which command enables you to determine the spanning-tree guard features that are enabled globally?
A. show spanning-tree
B. show spanning-tree summary
C. show spanning-tree active
D. show spanning-tree detail

ANS : B o D??

@coyo … B. show spanning-tree summary

@need2passswitch , thanks
which HSRP identifier can an end station use to find the default gateway at the data link layer?
A. router priority
B. MAC address
C. BIA
D. virtual IP address

ANS..C?

Passed, no big surprises. HSRP/VTP and LACP/STP lab, some tricky questions on LACP, couple of D&D on Stack/VRRP but use this site well and it will serve you well.

@coyo HSRP B

interface GigabitEthernet0/3
switchport access vlan 166
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 166,266,366
switchport mode trunk

Choose 2
1. The Switchport is in access mode
2. The Switchport is in trunk mode
3. The Switchport tags native vlan 1
4. The Switchport tags native vlan 166

If you have to choose 2 then it’s 2 and 3. Clearly the port is a trunk, and because the native VLAN isn’t mentioned on the port you can say it’s 1.

That is addressed to ONEWAY, not by him.

Which err-disable recovery command option enables a device to recover from an incorrect SFP state?
A. sfp-config-mismatch
B. gbic-invalid
C. port-mode-failure
D. link-monitor-failure
Answer: A o B???

@Stranger – I thought so too. So you are saying that the switchport won’t tag the packets on vlan 166 but only on VLAN 1

@Anonymous – B (sfp is a gbic so)

Passed yesterday, near 10 new questions, 1 drag & drop reworded… 1 d&d new ,lab and sim the same as on this site !

@blade, how much mark did you score? or lose?

@Oneway 840 points

Hello everyone. I am taking my exam in a few days, please let us know what Sim/Labs you get and also the drag and drop questions. I am reading the dump updated 1/9/2020, will that be enough to pass? Thank you for any advise.

@Blade which material or dumps did you use?

Sharing is Caring

I would like to provide Q1132 Vce and pdf file.

How can I share it

Passed yesterday with 915

D&D RSPAN
Labs LACP with STP Sim and HSRP

@Django congratulation ,,, which material or dumps did you use?