Share your SWITCH v2.0 Experience

Passed with with 9xx/1000

Got 44 questions and below are the structure ;

* 41 MCQ ( about 5 – 9 New Qusetions + 2 – D & D – From Aug Dump)
* LACP Lab

1. 11-13 Vlans configured in SW-A
2. Switchport trunk encapsulation dot1q not working in SW-A
3. ip default gateway x.x.x.x not needed.
4. Better to check sh run before Config

* HSRP Sim (Same – No Configuration Needed)
* STP – VTP Sim (Same – No Configuration Needed)

In LACP lab, do we have to create vlan 11,12 and 13 ?
it says : “SwitchA needs to be the root switch for vlans 11, 12, 13, 21, 22 and 23. All other vlans should be left are their default values”

SwitchA#show vlan

VLAN Name Status Ports
—- ——————————– ——— ——————————-
1 default active Fa0/1, Fa0/2, Fa0/5, Fa0/6
Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/13, Fa0/14
Fa0/15, Fa0/16, Fa0/17, Fa0/18
Fa0/19, Fa0/20, Fa0/21, Fa0/22
Fa0/23, Fa0/24, Gig0/1, Gig0/2
Po1
98 VLAN0098 active Fa0/3, Fa0/4
99 TrunkNative active

Hi BK,

Could you please confirm if those 2 D & Ds are from IP helper August or Certprepare August?

Do you remember the name of those D & Ds ?

Thanks

Today I have passed with a great score 9**.
All you need is covered here on this site, of course is possible to see new questions, but if you really understand the explanations provided on this site, you will be ok.
About the lacp with stp lab:
Its asked especifically to configure only the physical interfaces.
So IN MY OPNION I do not believe Cisco has two versions of this lab, the only version is that, when you have to put all configurations on the physical. Probably people have been created this myth about this lab, and after that was born a second version of this lab. It’s true on the real world you have to configure portchannel, but Cisco is Cisco and this is the Cisco way, always kidding with our knowledge and our attention to detail as well.
Other Simlets were: vtp3 and hsrp. It seems Cisco abandoned dot1x lab and MLS/eigrp as well, according the last comments from people that have passed too.

Alhamdulillah thank to Almighty ALLAH
Passed 878 Marks
Guys exam was so easy same Lab LACP Simlet HSRP and VTPv3 and 3 DnD TACACS+Radius, STP Component and GLBP
no need to configure Interface port-channel
2 New questions only others from same dumps which i shared last time please go with that and pass your exam easily.

Hi Guys, I am a premium member at certprepare. I just want to check. Do I need to learn on the “lab sim” under SWITCH 300-115? Or shall I just focus on the following?

HSRP Simulator
VTPv3 Simulator
LACP with STP Simulator
AAAdot1x Simulator
MLS and EIGRP Simulator

Please do help to advise. Thank you!

@Yonek no need bro LACP HSRP VTPv3 is enough for pass

PASSED 9**

Labs are same. I choose answer A for the questions 3 & 4 in VTPv3.
several days ago someone posted around 35 question on this forum ..it was my exact exam today.
You can take around 30 minutes comfortably for LACP with STP sim since this is the only configurable lab you will ever get. DO NOT PANIC.. even if y take more times, because u will have ample of time to finish other questions.configuration need to be configured via physical port. I’m a premium member.

For VTPv3, SW1 is the primary master because in the vtp status command out put ” DESCRIPTION” says SW1 as a primary.

HSRP sim is same
next T-shoot..

@Yonek,

HSRP Simulator
VTPv3 Simulator
LACP with STP Simulator
Came today…

LACP with STP..
ping was successful.
port-channel came up right away.

Hello Waseem

Can you share the dumps? my email is {email not allowed}

@Waseem

congrats for passing your exam with great score brother, I have one questions for you, please tell me if this site alone is enough for passing the exam, My exam is within few days. Thanks

laura.navarro.mendo at gmail dot com

@Saji

congrats for passing your exam. we would like to pass it with flying colors as well. Can you please tell us where to find the 35 posted questions? can you at least mention the page number of the comment section where we can find the 35 posted questions. thanks

!!!!

1. Which statement about VSPAN is true?
A. It can monitor ingress and egress traffic on the source VLAN
B. It sends all VLAN traffic to the destination port regardless of the VLAN’s status
C. It can monitor destination port traffic that belongs to a source VLAN
D. It can monitor token ring VLANs

2. Which mechanism is specific for RSPAN and not for SPAN?
A. source port
B. monitor port
C. reflector port
D. redundant port
E. destination port

3. Which two statements about source port monitoring in a SPAN are true? (Choose two.)
A. Traffic through a destination port can be copied and included in the SPAN session.
B. The entire EtherChannel must be monitored.
C. It can monitor only FastEthernet and GigabitEthernet port types.
D. It can monitor individual interfaces within a port channel.
E. It can monitor ingress and egress traffic.

4. A switch has been configured with the vlan dot1q tag native command. Which statement describes what the switch does with untagged frames that it receive?
A. Untagged frames are forwarded via the default VLAN
B. It drops the untagged frames
C. The trunked port is put in err-disable state
D. Untagged frames are forwarded via the native VLAN

5. Which two operational attributes can be checked for EtherChannel ports that are in err-disabled state?
A. Port mode B. Port cost C. Duplex D. DTP E. VLAN

6. Which command do you enter to enable Dynamic ARP Inspection for VLAN 15?
A. SW1(config-vlan)# ip arp inspection vlan 15
B. SW1(config-vlan)# ip arp inspection trust
C. SW1(config-if)# ip arp-inspection trust
D. SW1(config)# ip arp inspection vlan 15

7. Which two statements are true about port security? (Choose two)
A. It is used on EtherChannel bundle.
B. It must be used on the switch interface.
C. It can be configured for SPAN.
D. It is configured on an access port.
E. ?

8. Which two statements about static MAC addresses are true? (Choose two)
A. They are configured without an aging time.
B. They have a default aging time of 300 seconds.
C. They supersede dynamically learned MAC address.
D. They can be configured on multiple interfaces in the same VLAN.
E. They have a default aging time of 60 seconds.

9. Which security feature inspects ARP packets based on valid IP-to-MAC address bindings?
A. BPDU guard
B. port security
C. DAI
D. IP source Guard

10. In which two ways can a port respond to a port-security violation? (Choose two)
A. The port enters the err-disabled state.
B. The Security Violation counter is incremented and the port sends an SNMP trap.
C. The Security Violation counter is incremented and the port sends a critical syslog message to the console.
D. The port triggers an EEM script to notify support staff and continues to forward traffic normally.
E. The port immediately begins to drop all traffic.
F. The port enters the shutdown state.

11. Which three features can be optimized by using SDM templates? (Choose three)
A. port security
B. Trunk
C. VLAN
D. access
E. DHCP snooping
F. routing

12. What types of SDM templates you can use in switch? (Choose three)
A. Access B. Default C. Routing D. VLANs E. ? F. ?

13. Which two statements about default FHRP behavior are true? (Choose two)
A. A backup GLBP active virtual gateway can become active only if the current active virtual gateway fails
B. Preemption is enabled by default
C. Unless specifically configured, the priority of an HSRP router is 200
D. A standby HSRP router becomes active if it has a higher priority than the priority of the current active router
E. A VRRP backup virtual router becomes the master router if its priority is higher than the priority of the current master router

14. How many AVGs can be elected by GLBP member?
A. 1
B. 2
C. 4
D. 6

15. Which option is the minimum number of bindings that the DHCP snooping database can store?
A. 1000 bindings
B. 2000 bindings
C. 5000 bindings
D. 8000 bindings

16. A switch has been configured with the VLAN dot1q tag native command. Which statement describes what the switch does with untagged frames when it
receives on a trunked interface?
A. Untagged frames are forwarded via the default VLAN
B. It drops the untagged frames
C. The trunk ports is put in err-disable state.
D. Untagged frames are forward via the native vlan

17. Which two commands display the VLANs that are present in the VLAN database? (Choose two.)
A. show running-config
B. show vlan database
C. show vlan brief
D. show vlan
E. show vlan id

18. Which two commands do you enter to add VLAN 20 on a switch VLAN configuration file? (Choose two.)
A. switchport trunk native vlan 20
B. switchport access vlan 20
C. vlan 20
D. switchport trunk allowed vlan 20
E. encapsulation dot1q 20
19. Which two commands do you enter to add VLAN 15 on a switch VLAN configuration file? (Choose two.)
A. switchport trunk native vlan 15
B. switchport access vlan 15
C. vlan 15
D. switchport trunk allowed vlan 15
E. encapsulation dot1q 15
20. Refer to the exhibit. A single server in Company 123 is connected via EtherChannel to a single upstream switch. Which EtherChannel load balancing method on the switch makes optimal use of the redundant links as traffic flows from the routers to the server?
A. source MAC address
B. source IP address
C. source and destination MAC address
D. destination MAC address
21. Which command enables root guard on a Cisco switch?
A. Switch(config)#spanning-tree guard root
B. Switch(config)#spanning-tree root guard
C. Switch(config-if)#spanning-tree guard-root
D. Switch(config-if)#spanning-tree guard root
E. Switch(config-if)#spanning-tree root guard
22. Which two configuration requirements for port security are true? (Choose two.)
A. Port must be in access mode
B. Port security must be enabled on the port level
C. Port must be in interface VLAN mode
D. Port security must be disabled on the port level
E. Port must be in encapsulation mode
23. Which two configuration requirements for port security are true? (Choose two.)
A. The port must be part of a trunk.
B. Port security must be enable at the port level
C. Port security must be enabled at the global level.
D. The port must be SPAN port.
E. The port must be part of an EtherChannel bundle.
F. The port must be in access mode.
24. Which type of failure has occurred, if a link fails and the MEC successfully redistributes the load among the remaining operational links?
A. multiple MEC link failure
B. standby switch failure
C. active switch failure
D. single MEC link failure
25. Which command do you enter on a device so that users are automatically placed in enable mode after they authenticate with TACACS+?
A. aaa authorization exec default group tacacs+ if-authenticated
B. aaa authorization exec default group tacacs+ local-case
C. aaa authorization exec default group tacacs+ enable
D. aaa authentication exec default group tacacs+ if-authenticated

26. Which two statements about the local user database are true? (Choose two.)
A. For console connections, it can be used only as a backup authentication method.
B. It can be configured to grant a user-specific privilege level.
C. It can store passwords in clear text only.
D. For VTY connections, it can be used only as a backup authentication method.
E. It can be used as the only method of authentication or as a backup for other methods.
27. What is the value of the TPID/tag protocol identifier in dot1q?
A. 0x8100
B. 0x8a88
C. 0x8b45
D. 0x8200
28. Which two TLVs are included in Cisco Discovery Protocol advertisements? (Choose two.)
A. Network Policy TLV
B. VTP Management Domain TLV
C. System Name TLV
D. Inventory Management TLV
E. Native VLAN TLV
29. Which two statements about sticky MAC address learning are true? (Choose two.)
A. A single device can learn up to three sticky MAC addresses.
B. Devices can learn sticky MAC addresses dynamically.
C. Learned addresses are saved to the startup configuration file by default.
D. Learned addresses are saved to the running configuration by default.
E. Learned addresses are automatically preserved when the device reboots.
F. It can be used only on devices that operate in a single layer.
30. After you connected a host to switch port G0/1, the port is error disabled. Which command can you enter to determine the reason?
A. show interfaces g0/1 status
B. show log
C. show run interface g0/1
D. show ip interface brief
31. Refer to the exhibit.
Which option is the most likely explanation of the duplicate address message logged?
A. spanning-tree loop
B. HSRP misconfiguration
C. a PC with IP of 10.10.1.1
D. a hardware problem
32. Which feature can prevent ARP poisoning attacks on a device?
A. Dynamic ARP Inspection
B. DHCP snooping
C. MAC snooping
D. CGMP snooping
E. Dynamic MAC Inspection
F. Static ARP Inspection
33. Which two device types does DHCP snooping treat as untrusted in an ISP environment? (Choose two.)
A. end host devices
B. customer edge services
C. user-facing provider edge devices
D. provider edge devices
E. provider devices
34. You want to correctly configure IP Source Guard on a switch. Which two tasks must you perform? (Choose two.)
A. Enable DHCP snooping on the switch.
B. Enable DHCP packet validation on the device.
C. Configure the DHCP snooping relay.
D. Enable DHCP option 82.
E. Configure the ip verify source vlan dhcp-snooping command.
35. Refer to the exhibit. An engineer is configuring a trunking port-channel between switch 1 and switch 2 and receives an error message on switch 1. Which
option corrects this error?
A. enabling BPDU guard on interface Fa0/23 of switch 2.
B. enabling BPDU guard on interface Fa0/23 of switch 1.
C. disabling BPDU guard on interface Fa0/23 of switch 2.
D. disabling BPDU guard on interface Fa0/23 of switch 1.

Drag and Drop – PVST+ / Rapid PVST+ / MSTP
PVST + 802.1d standard + default STP
RapidPVST + 802.1w standard + has Discarding port state
MST + 802.1s standard + group vlan int instance

Drag and Drop – SPAN Source and Destination Ports
Source port: 1. It can be trunk or an access port
2. It can be monitored as a bundled logical port or as individual physical ports
3. Multiple VLANs can be included in a single session
Destination switch:
1. It acts as the monitoring port
2. It is not supported as part of a VLAN
3. Its original configuration is overwritten by the SPAN configuration

Drag and Drop – AVG/AVF/ARP/Gateway Priority
AVG – Assign MAC for client in subnet
AVF – forward traffic sent to MAC
ARP – this protocol to learn MAC when know IP
Gateway priority – use to elect active virtual gateway
Drag and Drop – RADIUS / TACACS+
Sim LACP, VTP3 & HSRP

@Saji

thanks a lot brother. we real appreciate

Which two circumstances can cause a port to errdisable? (Choose two)
A. It is connected to a host with an NIC that is unable to recognize
B. The switch incurred a port security violation
C. It detected a collision
D. It learned a new MAC address
E. It detected a peer with a matching duplex
Answer: B D o A B

Which two circumstances can cause a port to errdisable? (Choose two)
A. It is connected to a host with an NIC that is unable to recognize
B. The switch incurred a port security violation
C. It detected a collision
D. It learned a new MAC address
E. It detected a peer with a matching duplex

Answer: B D

@Saji don’t suppose you have the answers to the questions to make my life easier please 😊

Testing tomorrow in exactly 24hrs: I had cleared SWITCH in the past but lol it expired! So had to do it again, Things have changed a lot after my first exam. However, the labs are still the same. “No shutdown” command is very important even if “shutdown” is not in the running configuration.

Guys, Everybody is talking about August Dump! Could anyone please help me or guide me to find that please?

@ONEWAY contact me,
I have the most updated dump, I examine myself on Wednesday {email not allowed}

I have the most updated dump, I examine myself on Wednesday adrian.delgado52 @ yahoo dot com

hello anyone with the latest dumps please share with me via my email
princesselicious @ gmail dot com

Dears Waseem and Saji,
Congrats for passing and thanks for your feedback..
I’m re-certifying and as ONEWAY said, almost same questions for long time ..
@Solid I will get in touch for the updated dump ..All the best to all ..

Rememebr All Cisco exams will be replaced by 23rd of Feb2020 so plan accordingly .

A friend told me that when I put in SWB
interface range 0 / 3-4
—-> placed
switchport mode trunk (I didn’t let it come out as an error message) some auto or encapsulation

I continued doing the configuration at the end of the error message on fa0 / 4 and vlan.

when reviewing the configuration only the configuration was for fa0 / 3

I set the fa0 / 4 individually as well and no error came out
to ping from the swB to ip router-
 that is normal ??
How is it validated that the LACP-STP lab is fine?

Guys, Could you please anyone help me with D&D & the Ip-helper?

Hi everyone, today I passed the SWITCH exam with 889/100. The questions are mostly found here and in IPHelper, LABS are the usual ones, LACP-STP, HSRP, VTP3, D&D are from HSRP vs VRRP, Stackwise vs. VSS.
I want to thank this forum for the invaluable help!
Now I will try to pass the ARCH before Feb 23 …

@Eledu congrats, is the premium dump valid ?

Guys, Can anyone guide me to IP-Helper please?