Home > VTPv3 Sim

VTPv3 Sim

February 11th, 2017 in Lab Sim Go to comments

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.

VTP_Topology.jpg

Question 1

Explanation

To comply with the configuration of other switches, we need to get VTP configuration of Sw1 or Sw2. On Sw1 use the “show vtp status” command:

Sw1_show_vtp_status.jpg

From this output we learn on Sw1:
+ VTP is running version 3
+ VTP Domain is “CCNP”
+ Sw1 is the VTP Primary Server (we will explain about Primary Server later. Now just understand it is in VTP Server mode)

So on the New_Switch, the VTP Domain must match. New_Switch should run VTP version 3 if if can (but it is not a must as VTP version 2 is compatible with VTP version 3). The New_Switch is connecting to hosts so it is in Access Layer so it should be configured as a VTP Client (although Transparent mode is acceptable) so there are only two suitable choices D & E.

From the exhibit, the New_Switch is connecting to a host in VLAN 100 so its E0/0 interface should be in VLAN 100 -> only D is correct.

Question 2

Explanation

On Sw1 & Sw2 we can check with the “show interfaces trunk” command:

Sw1_show_interfaces_trunk.jpg

Sw2_show_interfaces_trunk.jpg

Sw1 & Sw2 are connected through E2/3 & E2/3 so we can see the native Vlan on these trunks are 99. We should check both Sw1 & Sw2 to see if the Native Vlan on both sides match.

Question 3

Explanation

In VTP version 3, there are two additional fields under the output of “show vtp status” command. They are:
+ “Primary ID”: The MAC address of the Primary Server
+ “Primary Description”: The hostname of the Primary Server

The Primary Server is used on VTP version 3 to avoid the bad behavior in version 2. In VTP version 2, a VTP client (or Server) can be taken out of the network. When it comes back, it can overwrite a VTP Server if its Revision number is higher. This problem no longer exists in VTP version 3 because there is only one VTP Primary Server at a time. Only a VTP Primary Server can create new VLAN.

After creating new VLAN, the VTP Primary Server will advertise its VLAN database to other VTP clients/servers so in fact answer A is not correct. In this question you just need to check if Sw1 or Sw2 is the VTP Primary Server then we can create both VLAN 500 & 600 on it. Then it will advertise these VLANs to other switches.

Sw1_show_vtp_status_primary_server.jpg

From the output we see Sw1 is the Primary Server so we should configure VLAN 500 & 600 only on this switch.

Note: If the above output shows the roles of Sw1 and Sw2 are “Server” only (not “Primary Server”) then we should choose: A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2

Note: To make a switch a Primary Server, issue the “vtp primary vlan” under privilege exec mode. For example:

Sw1#vtp primary vlan

Question 4

Explanation

To configure private VLAN we have to change VTP (even version 3) to Transparent mode. In fact, to disable VTP pruning on Sw4 (in Client mode) we also have to change to VTP Transparent mode so answer C can be understood as “change SW4 to Transparent mode” so it is the best choice.

Note: Unlike VTP version 1 and 2 in which VTP pruning is enabled on VTP Server only, VTP version 3 requires VTP pruning must be enabled on all the switches in the VTP domain so we can also disable VTP pruning on each switch separately. Here is the link for your reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/12-2_55_se/configuration/guide/3750xscg/swvtp.html

“With VTP versions 1 and 2, when you enable pruning on the VTP server, it is enabled for the entire VTP domain. In VTP version 3, you must manually enable pruning on each switch in the domain.”

Comments
Comment pages
  1. moonthinker
    April 18th, 2016

    Could someone please send me a valid dump of 300-115, please
    {email not allowed}

  2. moonthinker
    April 18th, 2016

    Could someone please send me a valid dump of 300-115, please
    kmmoon3419 gmail.com

  3. KB
    April 22nd, 2016

    Hi GUYS..

    I ONLY SEE THE ANSWERS FOR THIS LAB….WHERE ARE THE QUESTIONS?

    THANKS IN ADVANCE

  4. Bola
    April 26th, 2016

    thanks God , Pass today , 191 still valid
    HSRP , AAA, LACP
    take care in LACP check your configuration ( Show running-conf) because some commands not appear so did it again , ( (conf)#Interface range fa 0/3-4 ) not supported in sim

  5. worto03
    April 27th, 2016

    A few people have posted the same thing now, I also see no questions?

    I see the word Question x in red then Explanation in green with the answer but no actual question.

    Are the questions on another page somewhere or do you have to download the packet tracer files to get them?

  6. Ran
    May 2nd, 2016

    Could anyone please kindly send me valid 300-101,300-105 and 300-135 dump. Vce or PDFs
    Nkssujith at yahoo dot com.

  7. dudu
    May 2nd, 2016

    passed today.

    40 questions
    drag / drop CDP
    aaa

    VTP sim / diagram
    diagram above [but NOT same questions]
    * what is virtual MAC
    *What percentage of traffic on R1 100% [Cause R1 is the active ]

    ————–
    note:
    in this section, i found confusing, but gave serious thoughts and came to the conclusion for the first one. [ “a” below, dont remember b or d ], show stand, and you see in E0/1 on R1 which is the ACTIVE router ! what will happen if E0/1 goes down ?
    *if E0/1 went down and recovered:
    question:
    a -the percentage of the E0/1 value will be decremented to 40
    b- bla bla bla bla
    c- the percentage of the current E0/1 will be incremented to 40
    d- bla bla bla
    —–

    Another thing to note in the exam is that the ANSWERS are not in the same position as in the 191q or other dumps!!! My goodness, i prepared and read the questions… at first glance, it seemed as if i was they changed the questions!! but took my time to read slowly, 2x the answers and found out they were same. [some questions, not all ]

    since this is fresh in my head now, another point to make:

    SIM with AAA

    * Its specifically said; ALL CONFIG BE UNDER PHYSICAL INTERFACES
    *Frankly, the only area i got stuck “thinking”, “thinking” is the mention of:
    HOSTS of subnet 172.140.46.0 /24 only on vlan 20 should be allowed

    * well during configuration of aaa and so on, no issue. But when i came to the DSW1 and configuring the access list..i got stuck, thinking: [ here is my point ]
    * REMEMBER THEY SAID “NO” NAME LIST
    access-list standard 10
    permit ip address 172.140.46.0
    {right here was my problem, remember they said host in 172.140.46.0/24}
    {if you put a context sensitive help. “?” infront of the ip above, it ask for WILDCARD BITS }
    eg

    permit ip address 172.140.46.0 ?
    A.B.C.D Wildcard bits

    {if you hit enter will it accept the 172 .140.x.x range or 172.140.46.x range ?} AHA!

    I choosed :
    access-list standard 10
    permit ip address 172.140.46.0 0.0.0.255 [24 bit mask ]

    vlan access=map PASS10 10
    match ip address 10
    action forward
    exit

    vlan access-map PASS10 20
    action drop
    exit

    vlan filter PASS10 vlan-list 20
    copy run start [SAVE| !!
    ——————————

    personal advice:
    i was in a very tight budget, i read about people going for second try etc.. goodness!
    i was in an airconditioned room for the exam and sweating !!! if you i hit continue without being sure, i could loose it [ 250$] ! , i took my time and rushed through the Q & A that came as in dump and when the LABS came, i got lot time to play with, plus i decided to practice with real equipments before exam.

    scored 9xx

    – .. . ……90%
    infrasctructure securtiy 100 %
    – – – — – -86%

    * any question: im ready to give back, please ask.

    goodluck

  8. Ramiro
    May 3rd, 2016

    @dudu
    Thanks for sharing your experience! According to your post, are there new question in the HSRP Sim? Is there a new lab and is the VTP Sim? When you are talking about config in physical interfaces, I think your are referring to LACP-STP lab but after that you start to talk about AAA Sim. Just please clarify, because some of us are confused.
    Thanks man!

  9. alphastate
    May 9th, 2016

    On question 1 sim above, to get all of the correct information, you need to execute the “show vtp password” command in addition to the “show vtp status” command because the vtp password is not shown in the output of the “show vtp status” command.

  10. Anonymous
    May 12th, 2016

    If anyone has premium VCE file for ccnp switch or tshoot please send it to: it elitist at google

  11. elite
    May 12th, 2016

    if any1 has the premium VCE file for ccnp switch or tshoot please send it to: it elitist at google

  12. Nwaxx
    May 19th, 2016

    @ Dudu
    Thanks for the advice, please can anyone send the 191q to me on nwaxx @ yahoo.com

  13. Anonymous
    May 20th, 2016

    VTP version 3 is able to publish private vlan information. You do not need to set vtp version 3 to transparant mode: https://networklessons.com/switching/vtp-version-3/

  14. Nadeem
    May 25th, 2016

    Hi All,

    Today I have Passed CCNP Switch with 958/1000 marks…

    Thanks to certprepare…

    LABS: AAA-dot1x, STP-LACP, HSRP, CDP/LLDP Drag and Drop

    191q is all valid…

    All the best guys…

  15. ysn
    May 25th, 2016

    @ dudu
    congratulation you passed the exam, can you share your 191q file please btt_ysn AT yahoo dot com

  16. M
    May 27th, 2016

    dudu, fyi thats VTP sim not HSRP, thats why questions are different

  17. M
    May 31st, 2016

    question 3, are you sure you have to Configure VLAN 500 and VLAN 600 on SW1 only
    and not Configure VLAN 500 VLAN 600 on both SW1 SW2?
    thanks

  18. Anonymous
    June 13th, 2016

    congratz to those that passed.

    can someone send latest dump to redatmyfitnesspal AT gmail dot com?

  19. first-time
    June 16th, 2016

    Please, what is main “Use the console access to the existing and new switches to configure and verify correct device configuration.” ??

    thanks,,,

  20. Wally
    June 22nd, 2016

    Yep – where are the questions please on https://www.certprepare.com/vtpv3-sim

  21. zee
    July 4th, 2016

    I faced rules in CCNA exam are these still exist in the CCNP Swith exam??
    1)Using help(?)
    2)Pressing tab to complete the command
    3)If it shows invalid command error?
    4)can I use short command??
    If we follow these things, points deduct or not
    I have confusion about this please help me

  22. X)X)
    July 14th, 2016

    yes you can use it and no ,no marks will be deducted if you use any of the above shortcuts.

  23. first-time
    July 21st, 2016

    PLS, for VTPv3 Sim is it required to configure the new switch withe the selected answer or only we have to choice the correct answer?

  24. wantknow
    August 4th, 2016

    Hi everybody,
    I am ready for the switch exam. I heared from 191q dump. just to be sure. Can anyone send it to me {email not allowed}. I will apreciate it.
    Thanks in advance

  25. wantknow
    August 4th, 2016

    wantknow2000 @ yahoo . de

  26. marco
    August 7th, 2016

    wantknow, your mail is not working :( I have the 191Q in PDF format.

  27. Bullet.Speed
    August 8th, 2016

    Hi marco,
    Can you please send me these dumps on bullet.speed99 @ gmail . com

  28. firray
    August 8th, 2016

    anychance having those 191q dumps

  29. marco
    August 8th, 2016

    firray: mail?

  30. vishal
    August 9th, 2016

    marco can you send me the 191Q dumps at umbayo at gmail dot com

  31. need2pass
    August 10th, 2016

    Marco ARE THE LABS still accurate HSRP LACP and AAA dot1x?
    >> electronic mail >>j e s s e 7 1 2 at h o t m a I l dot com<<
    please send me what you have subject ccnp

  32. pipi
    August 11th, 2016

    Dear Marco, can you also send dumps (pdf) to allcertif @ yahoo.com. Thanks

  33. need2passforsure
    August 15th, 2016

    Can somebody please clarify this? I’m having problems on this.

    Question 3

    You are adding new VLANs: VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?
    A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2
    B. Configure VLAN 500 and VLAN 600 on SW1 only
    C. Configure VLAN 500 and VLAN 600 on SW2 only
    D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
    E. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.

    Answer: B <—–isn't it suppose to be A? I've seen in a lot of dumps that it is A.

    I hope someone can clarify this. Thank you.

  34. Anonymous
    August 15th, 2016

    Q3
    @need2passforsure:

    I believe You are right & the above answer is wrong
    To answer any question, first we need to understand what the question wants or what it’s looking for. I think the only way to do this is as follows:

    SW1(config)# Spanning-tree vlan 500 root primary
    SW1(config)# Spanning-tree vlan 600 root secondary

    SW2(config)# Spanning-tree vlan 600 root primary
    SW2(config)# Spanning-tree vlan 500 root secondary

    As you see, the only way to do this is to config both switches. Yes VTP does propagate messages to all switches, but how come you config the last 2 lines withOUT touching SW2!?

  35. Anonymous
    August 15th, 2016

    Above Anonymous comments are mine.. I took 300-115 test last week and yes 191Q dumps were valid “Aug 5th”

  36. need2passforsure
    August 15th, 2016

    @Anonymous,

    Thank you for the clarification. There is no way to do it other than what you’ve mentioned. Even the other VTP Lab SIM needs clarification.

  37. Wyle
    August 16th, 2016

    @need2passforsure

    Which one? I can help with it. Can you please copy the link here & ask the question there.

  38. Alberto
    August 16th, 2016

    TO need2passforsure, be careful when u read the question, it says witch “CONFIGURATION STEP” is valid…SO…all the answers are about creating vlans…so u have VTP activated and u have to configure it just in the PRIMARY SERVER (SW1) …So there u go. (Answer B)

  39. nabs
    August 19th, 2016

    Can someone please send me the 191Q dump or as pdf? Thanks!!!
    maxusbaxus (at) gmail (dot) com

    Thanks guys!!!

  40. Wyle
    August 20th, 2016

    @nabs: I sent – check your email

  41. Nel
    August 22nd, 2016

    Can someone send the latest dumps on my email also your training materials. I will have my exam this comming august 30

  42. Nel
    August 22nd, 2016

    Can someone send the latest dumps on my below email. also your training materials. I will have my exam this comming august 30. {email not allowed}

  43. medueleelculo
    August 22nd, 2016

    anybody knows why all the dumps disappear from examcollection.com?
    please send me the lastest dumps to newk349 at hotmail dot com!!

  44. dirttrid
    August 22nd, 2016

    Can you please share your 191q file? {email not allowed}

  45. dirttrid
    August 22nd, 2016

    Can you please share your 191q file? dirt (at) bk (dot) ru

  46. Maverick
    August 23rd, 2016

    Does anyone have the 191Q dump avail, please email me: tacrr6 (at) gmail (dot) com really will appreciate it..

  47. vicram
    August 25th, 2016

    Hi Nabs and Wyle,

    I, m gonna give exam this August 27 .
    Can anybody please share ur 191q dumps to the below mail please I cannot afford next exam cost even I prepared some nervous.

    v I c r a n 4 u AT GMAIL DOT COM
    Small letter is my id
    Thanks in advance

  48. vicram
    August 25th, 2016

    vicran4u AT GMAIL DOT COM

  49. Yuriy
    August 25th, 2016

    Hello to everyone.
    I will going to pass SWITCH 300-115 exam in 20September.
    I am really worried to pass this exam.
    I have 3 CCNA sectification, and I am worried about to renew them.
    Can someone send me the 191Q dump, pdf the best.
    Thanks.
    hts.yuriy AT gmal.com

  50. Yuriy
    August 25th, 2016

    hts.yuriy AT gmail.com

Comment pages
  1. No trackbacks yet.